GUIDE LIBRARY · FREE2 guides

Furnace Quote Breakdown: Gas, Oil and Electric Replacement Costs

Break a furnace quote into six lines — equipment, labor, ducts, venting, electrical and permits — with dated U.S. ranges, not just a total.

2actionable guides
2popular entries
0paywalls
EXAMPLES

Six real replacement scenarios: match the fuel and existing system before the total

Ranges are public U.S. market figures, dated in each line: Fixr gas (updated 2025-01-31), electric (2025-08-29), oil (2026-01-12) and repair (2025-08-29), plus HVAC.best (published 2026-06-27); accessed 2026-11-03. The two publishers scope their ranges differently, so do not average them. Every total below is a worked example, not a quote.

1,500 sq ft, climate zone 2, existing ducts: 20 kW electric furnace swap$1,600–$3,200 installed (Fixr electric, 2025-08-29); same-size replacement $900–$2,000

This is the cheap path on installation: no gas line and no combustion venting. Fixr puts direct-replacement labor at $300–$600 and new-install labor at $1,000–$1,500. Cheap to install is not cheap to own: electric furnaces fit zones 1–3 and smaller homes, and in a cold climate the operating cost can erase the install savings. Check the 240 V circuit and panel capacity first; if the panel needs an upgrade, Fixr adds $1,500–$4,000, a line that is often missing from the first quote.

2,000 sq ft, existing ducts, 80% single-stage gas: same-fuel replacement$4,000–$8,000 installed (Fixr gas, 2025-01-31); same-fuel replacement also $4,000–$8,000

For a 2,000 sq ft home, Fixr's typical high-efficiency replacement is about $6,000. The $3,000 low end is a moderate-efficiency unit with no modifications; the $12,000 high end includes new ductwork. Labor is $500–$3,000, most often $1,500–$2,000. Same size, same brand and same location is the cheap case; changing brand, size or venting adds hours. HVAC.best's $3,800–$12,000 gas range is wider because it includes high-efficiency equipment and complex retrofits; do not use its ceiling to dismiss Fixr's average.

2,000 sq ft, 96% condensing gas: new PVC venting and condensate$6,000–$10,000 installed (Fixr gas high-efficiency band, 2025-01-31)

A 90%+ condensing furnace needs its own intake/exhaust and a condensate drain, and many old chimneys or metal flues cannot be reused. Fixr notes that high-efficiency labor runs higher because a drain is often added. The quote should show vent material, condensate handling and any chimney liner as separate lines, not just "high-efficiency furnace." If the ducts leak, settle the $1,900–$6,000 duct budget first; a 96% furnace on leaky ducts loses the fuel savings through the ducts.

Northeast oil furnace with an existing above-ground tank: furnace only$4,000–$10,000 installed, $4,900 average (Fixr oil, 2026-01-12)

The variable in an oil quote is rarely the furnace itself; it is the tank, flue and permit. Fixr puts labor at 30%–60% of the total ($75–$150/hour, 4–12 hours), old-unit removal at $50–$400, and permits at $50–$1,500. An above-ground/indoor tank replacement adds $1,000–$4,600; an underground tank adds $1,500–$6,000. If the tank belongs to the supplier, settle who handles leaks and soil testing before signing.

Ducts are being replaced too: gas furnace plus new ductwork$10,000–$12,000 combined (Fixr gas FAQ, 2025-01-31); ducts alone $1,900–$6,000

Fixr's gas page gives a useful ceiling: about $10,000–$12,000 for a 2,000 sq ft high-efficiency furnace plus new ducts. Its oil page lists ducts at $1,400–$6,000 and its electric page at $1,900–$6,000; those scopes differ, so do not mix them. Do a Manual J load calculation and a duct-leakage/return-air check before choosing repair, seal or replacement. Replacing the furnace without touching the ducts is the classic high-efficiency-furnace, low-efficiency-system overpay.

15-year-old furnace with a failed heat exchanger: repair or replaceHeat exchanger $1,346–$2,673; blower $562–$1,045; control board $390–$725 (Fixr repair, 2025-08-29)

A general repair runs $349–$650, $485 average, but the heat exchanger is a different decision: Fixr prices it at $1,346–$2,673 and the labor is heavy. A practical rule is to replace when the furnace is 15–20 years old, one repair approaches half the replacement price, or a heat exchanger/CO risk appears. Do not price only this visit; add the chance of a second repair and a no-heat stretch during the heating season.

FAQ

Eight questions to settle before you sign

Two quotes differ by $2,000 — which six lines do I compare first?

Make both contractors quote the same six lines: (1) equipment model, BTU and AFUE; (2) labor and hours; (3) gas/electrical connection; (4) venting, condensate and chimney; (5) ducts and return air; (6) permit, old-unit removal and commissioning. Fixr puts gas labor at $500–$3,000; its oil page says labor is 30%–60% of the total. The same total can hide completely different scopes and brands, so compare the lines before the bottom line.

Is an electric furnace always cheaper than gas because it costs less to install?

It costs less upfront — Fixr lists electric at $1,600–$3,200 installed and gas at $4,000–$8,000 — but Fixr also says electric furnaces fit climate zones 1–3 and smaller homes, and cold-climate operating costs are high. Gas costs more to install and usually less to run. Compare local electricity and gas rates, house size and insulation over five years, not just the first invoice.

Will a 90%+ furnace always pay back the difference?

No. A condensing furnace needs extra venting and a condensate drain; Fixr prices high-efficiency gas installation at $6,000–$10,000. Leaky ducts, poor insulation, a mild climate or a short ownership window can stretch the payback. Put the equipment premium, duct budget, rebates/tax credits and estimated annual fuel savings in one table. HVAC.best notes a federal tax credit of up to 30% (capped at $600) for qualifying furnaces, but eligibility and amounts must be checked against current rules.

Do I have to replace the ducts when I replace the furnace?

Not always, but inspect first. Fixr lists new ducts at $1,900–$6,000 on its gas/electric pages and $1,400–$6,000 on its oil page. If the ducts leak, the return is undersized or the sizing is wrong, a high-efficiency furnace cannot deliver its rating. Do a Manual J and a duct-leakage test; seal if possible, replace only what cannot be fixed. Compare the furnace-plus-duct total with the furnace-only total.

Why does the oil tank dominate an oil furnace quote?

Because the furnace is only one line. Fixr lists above-ground/indoor tank replacement at $1,000–$4,600 and underground tanks at $1,500–$6,000; old-unit removal is $50–$400 and permits are $50–$1,500. Check tank ownership, age, leaks and whether soil testing is required. If the supplier owns the tank, put leak responsibility and replacement obligations in the contract, not in a verbal promise.

Repair or replace an old furnace?

Start with the part. Fixr's general repair range is $349–$650 ($485 average), but a heat exchanger is $1,346–$2,673, a blower $562–$1,045 and a control board $390–$725. Replace when the furnace is 15–20 years old, one repair approaches half the replacement price, or a cracked heat exchanger/CO risk appears. Saving one repair bill is not worth a no-heat stretch and a second repair in the same season.

Who handles the permit and inspection?

Most jurisdictions require a permit for a furnace replacement, usually pulled by the licensed contractor. Fees vary widely: Fixr's oil page gives $50–$1,500, while HVAC.best gives a common $50–$300. Put who applies, who pays and who attends the inspection in the contract. Commissioning should include combustion analysis (gas/oil), static pressure, temperature rise, venting and CO testing. A quote with no permit or commissioning is not cheap; it moves the risk to you.

What should I check before signing?

(1) Model number and AHRI/efficiency certificate; (2) BTU sized by Manual J, not square footage alone; (3) labor scope, including old-unit removal and weekend/emergency fees; (4) venting, condensate, chimney and ducts; (5) gas/electrical connection and panel upgrades; (6) permit, commissioning and warranty split (unit/heat exchanger/labor); (7) payment milestones and rebate paperwork. Put three quotes on one sheet, make the missing line explicit, and negotiate scope before price.

01 · POPULAR

Popular topics

Start with the 2 most-read topics, or search everything.

02 · START HERE

Start here

Don't get lost: start with the picks, then expand by topic.

All 2 guides →
03 · ALL GUIDES

All content

Filter by keyword; each guide has steps, common mistakes and a checklist.

04 · HOW

How to use this site

STEP 01

Pick a real problem

Start from a recommendation or search, not the first page; find the problem you need to solve now.

STEP 02

Follow the steps

Each guide gives steps, common mistakes and a checklist; do the smallest step first, then iterate.

STEP 03

Review with the checklist

Check your work with the checklist; drop what does not fit and keep the repeatable process.

05 · WHY

Why read this

01

Not vague concepts

Every guide lands on steps, templates, mistakes and a checklist you can actually use.

02

No invented results

No promises of income, traffic or admission; professional topics state limits and point to experts.

03

Kept updated

Last updated 2026.11.03; content grows from feedback instead of one-off empty pages.

Affiliate disclosure: this page may contain affiliate links. We may earn a commission if you buy through them, at no extra cost to you.